Re: listener on windows

You nailed it. Unfortunately, the vip does not want to relocate itself. srvctl start nodeapps -n rac2 says unable to start listener, and when I check ipconfig again, the vip for node 2 is still on node 1. even after I did a srvctl stop nodeapps on rac1.

On Dec 16, 2007 4:16 PM, <krish.hariharan_at_quasardb.com> wrote:

> Andrew,
>
>
>
> I ran into something similar in Unix. The VIP got failed over to the first
> node due to an error. If this is the similar condition then verify using
> ipconfig on each node that the VIPs are plumbed on the correct node. I
> haven't worked on Windows but I would think that the crs_stat or equivalent
> command will tell you whether and where the resources are online. Or it
> could be the case of rac2-vip not in the ../etc/hosts file in node 2
>
>
>
> -Krish
>
>
> ------------------------------
>
> *From:* oracle-l-bounce_at_freelists.org [mailto:
> oracle-l-bounce_at_freelists.org] *On Behalf Of *Andrew Kerber
> *Sent:* Sunday, December 16, 2007 2:54 PM
> *To:* oracle-l
> *Subject:* listener on windows
>
>
>
> I have done a home rac installation in windows 2003. clusterware
> installed, and importantly vip ran correctly without error. HOwever, I
> cannot get the listener to start on the second node when I have it set up
> with this configuration:
>
>
>
> LISTENER_RAC2 =
> (DESCRIPTION_LIST =
> (DESCRIPTION =
> (ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC1521))
> (ADDRESS = (PROTOCOL = TCP)(HOST = rac2-vip)(PORT = 1521)(IP =
> FIRST))
> (ADDRESS = (PROTOCOL = TCP)(HOST = 10.12.1.120)(PORT = 1521)(IP =
> FIRST))
> )
> )
>
>
>
> If I remove the line wiht rac2-vip it will start. THe listener on the
> first node starts just fine with its corresponding line.
>
>
>
> I can ping the virtual ip to and from each node. I tried deleting the
> service and then starting the listener. Made no difference. Here is the
> error message. This doesnt have it, but usually there is something about
> listener error 1060 also:
>
>
>
> C:\Documents and Settings\Administrator>lsnrctl start listener_rac2
>
> LSNRCTL for 32-bit Windows: Version 11.1.0.6.0 - Production on 16-DEC-2007
> 15:48
> :10
>
> Copyright (c) 1991, 2007, Oracle. All rights reserved.
>
> Starting tnslsnr: please wait...
>
> TNSLSNR for 32-bit Windows: Version 11.1.0.6.0 - Production
> System parameter file is
> C:\app\Administrator\product\11.1.0\db_1\network\admin\
> listener.ora
> Log messages written to
> c:\app\administrator\diag\tnslsnr\rac2\listener_rac2\ale
> rt\log.xml
> Listening on:
> (DESCRIPTION=(ADDRESS=(PROTOCOL=ipc)(PIPENAME=\\.\pipe\EXTPROC1521
> ipc)))
> Error listening on:
> (DESCRIPTION=(ADDRESS=(PROTOCOL=TCP)(HOST=rac2-vip)(PORT=152
> 1)(IP=FIRST)))
> TNS-12545: Connect failed because target host or object does not exist
> TNS-12560: TNS:protocol adapter error
> TNS-00515: Connect failed because target host or object does not exist
> 32-bit Windows Error: 49: Unknown error
>
> Listener failed to start. See the error message(s) above...
>
>
> Ill keep working, but does anyone have ideas? Thanks...
> --
> Andrew W. Kerber
>
> 'If at first you dont succeed, dont take up skydiving.'
>

-- 
Andrew W. Kerber

'If at first you dont succeed, dont take up skydiving.'

--
http://www.freelists.org/webpage/oracle-l