Home » Developer & Programmer » Forms » Post-text-item error (merged 3) (Forms 6i)
|Post-text-item error (merged 3) [message #426659]
||Sun, 18 October 2009 01:24
Registered: May 2009
Location: United Arab Emirates
I am trying to write a post text item trigger in forms to fire on following conditions.|
1.I have one non base table block in form where the data from one table will get pulled from adj table based on parameters passed.
2.Upon clicking on check box the data from this block will get inserted into temporary table.
3.User can modify the qty field in the detail block .
What i need is he should not enter the qty greater than what is there in the base table block , eg it can be less.For this i wrote one post text item trigger but its giving error as post item trigger raised unhandled exception ora-01001.Please check the code below.
AND CGBCV_ITEM_CODE =:DETAIL.TEXT_ITEM137
AND ITEM_CODE =:DETAIL.TEXT_ITEM137
AND LOCN_CODE =:DETAIL.TEXT_ITEM181
AND CGBCV_BATCH_NO = :DETAIL.TEXT_ITEM179
AND ITEM_CODE =IU_ITEM_CODE
AND ITEM_UOM_CODE =IU_UOM_CODE;
WHERE ADJH_SYS_ID = ADJI_ADJH_SYS_ID
AND ADJI_ITEM_CODE =:DETAIL.TEXT_ITEM137
AND ADJH_TXN_CODE = :IP_REP_INFO.TEXT_ITEM170
AND ADJH_NO = :IP_REP_INFO.TEXT_ITEM108;
--FUNCTION TO CONVERT VALUES
O_DCONV_PL_TO_BU (:DETAIL.TEXT_ITEM137 , :DETAIL.TEXT_ITEM183 , :DETAIL.TEXT_ITEM184 , :DETAIL.TEXT_ITEM185 , :DETAIL.TEXT_ITEM186 , NULL);
OPEN C1 ;
FETCH C1 INTO M_BUOM_cODE,M_COST,M_MAX_LOOSE_1;
OPEN C2 ;
FETCH C2 INTO M_DUMMY;
IF M_DUMMY <= :DETAIL.TEXT_ITEM184 AND NVL(M_COST,0) <> 0 THEN
O_DCONV_BU_TO_PL (:DETAIL.TEXT_ITEM137, M_BUOM_CODE , :DETAIL.TEXT_ITEM186 , M_QTY , M_QTY_LS , NULL );
MESSAGE('YOU CANNOT INCREASE THE QTY');
[Updated on: Sun, 18 October 2009 09:20] by Moderator
Report message to a moderator
|Re: Post-text-item error (merged 3) [message #426672 is a reply to message #426659]
||Sun, 18 October 2009 15:24
Registered: June 2005
Location: Croatia, Europe
ORA-01001 means "Invalid cursor":Oracle|
Cause: Either a host language program call specified an invalid cursor or the value of the MAXOPENCURSORS option in the precompiler command were too small. All cursors must be opened using the OOPEN call before being referenced in any of the following calls: SQL, DESCRIBE, NAME, DEFINE, BIND, EXEC, FETCH, and CLOSE. The Logon Data Area (LDA) must be defined by using OLON or OLOGON. If the LDA is not defined, this message is issued for the following calls: OPEN, COM, CON, ROL, and LOGOFF.
Action: Check the erroneous call statement. Specify a correct LDA area or open the cursor as required. If there is no problem with the cursor, it may be necessary to increase the MAXOPENCURSORS option value before precompiling.
Check what you did wrong about it.
Anyway, as far as I can tell, your use of a cursor is wrong. There's no point in declaring it and fetching a single record before closing it. You can do the same with a simple SELECT statement.
Also, any kind of "validation" should be done in the WHEN-VALIDATE-ITEM trigger (not POST-TEXT-ITEM one).
[Updated on: Sun, 18 October 2009 15:24]
Report message to a moderator
Current Time: Mon Jun 26 08:49:07 CDT 2017
Total time taken to generate the page: 0.10674 seconds