Home » Developer & Programmer » Reports & Discoverer » how to install Report Server in Oracle 10g Release 2 (10.1.2.0.2)
how to install Report Server in Oracle 10g Release 2 (10.1.2.0.2) [message #415189] Sun, 26 July 2009 02:50 Go to next message
Shaheer
Messages: 50
Registered: June 2008
Location: Pakistan
Member
hi

i am using Oracle 10g Form developer release 2 (10.1.2.0.2)on window XP (SP-3).


rwserver -install command is not working in oracle 10g form developer release 2 (10.1.2.0.2). Please tell me how to install Report Server in Oracle 10g Form developer release 2 (10.1.2.0.2).

Thanks in advance.

Re: how to install Report Server in Oracle 10g Release 2 (10.1.2.0.2) [message #415193 is a reply to message #415189] Sun, 26 July 2009 03:27 Go to previous messageGo to next message
Sarah Aman
Messages: 80
Registered: July 2009
Member

hi
i was having the same problem in dv suite 10G(10.1.2) the report server was not starting.What i did?
I configured Lan card and now its working fine.
i suggest you to use lan card and after that just restart you are report server

run-cmd.choose your directory where installed Form and then use the following command.
rwserver server=anyname start


Sarah

Re: how to install Report Server in Oracle 10g Release 2 (10.1.2.0.2) [message #415208 is a reply to message #415193] Sun, 26 July 2009 06:15 Go to previous messageGo to next message
Shaheer
Messages: 50
Registered: June 2008
Location: Pakistan
Member
please check the attached image. i receive error when use rwserver server=pim start command


Please also explain how to configure LAN Card


thanks in advance
  • Attachment: error1.JPG
    (Size: 21.12KB, Downloaded 789 times)
Re: how to install Report Server in Oracle 10g Release 2 (10.1.2.0.2) [message #416148 is a reply to message #415193] Thu, 30 July 2009 20:12 Go to previous messageGo to next message
Shaheer
Messages: 50
Registered: June 2008
Location: Pakistan
Member
hi Sir,


rwserver server=name command is execute properly in Oracle 10g Release 2 (10.1.2.0.2). After the execution of rwserver server=name command a Report Server window appear which shows Report Server is in running Status. But when i want to call Report through Form an Error occur 'Unable to connect Report Server'.

Please help me what can i do to run reports through forms in Oracle 10g Release 2 (10.1.2.0.2). Please help me
Re: how to install Report Server in Oracle 10g Release 2 (10.1.2.0.2) [message #416186 is a reply to message #416148] Fri, 31 July 2009 00:58 Go to previous messageGo to next message
Sarah Aman
Messages: 80
Registered: July 2009
Member

hi
if your using dv suite(10.1...) without ip address u cannot call report it will always give u error'unable to connect or bind to report server'i preffer u to use lan card if u have switch.
Note:
always restart you are report server with this command
(rwserver server=reportservername or(choose your own server name)start)dont use batch=yes


sarah

[Updated on: Fri, 31 July 2009 01:06]

Report message to a moderator

Re: how to install Report Server in Oracle 10g Release 2 (10.1.2.0.2) [message #416304 is a reply to message #416186] Fri, 31 July 2009 09:42 Go to previous message
Shaheer
Messages: 50
Registered: June 2008
Location: Pakistan
Member
thanks for guide me
Previous Topic: Report
Next Topic: Capabilities of Discoverer
Goto Forum:
  


Current Time: Fri Dec 09 15:42:24 CST 2016

Total time taken to generate the page: 0.24030 seconds